=Lever=
{{cleanup}}

A '''lever''' (or '''lever tumbler''') is a [[lock]] design that uses flat pieces of metal (also known as levers) and a [[bolt]] as locking components. In this article, 'lever lock' does not mean a locking lever handle incorporating a cylinder locking device.
In most designs, the position of the levers prevents the bolt from retracting. When positioned properly, a gate in the lever allows the bolt to move (shot or withdrawn). Lever locks are historically one of the most popular lock designs, but use has declined as less expensive [[pin-tumbler]] locks have gained popularity. Lever locks are popular in Europe (specifically the UK) as residential and commercial [[door]] locks and on [[safe]]s. Safe-deposit boxes in banks around the world use lever designs heavily.

__TOC__

== History ==

A single locking tumbler was used on many Roman metal locks, often in association with wards. Most early door locks had no case, with a bolt and locking tumbler mounted on a backplate. From at least 13C, some locks had these components mounted in a wood stock without a backplate — this lock design is the Banbury lock (the reason for this name is unknown). These designs did not use fences and gates, but rather a simple pivoted tumbler or lever that the key had to move (typically, lift) out of the way in order for the bolt to move. Security was provided by traditional keyway [[Warded|warding]].

=== Barron lock ===
In 1778, [[Robert Barron]] patented [BP1200] the principle of all modern mechanical security locks — the double-acting movable detainer. His patent describes 'the gating or racking to allow a stump on the tumbler to pass through the bolt, or an opening in the tumbler to allow a stump on the bolt to pass through.' These two (of several possible) realisations of the double-acting movable detainer principle are now usually described as 'lever locks'. Barron's was the first lever lock that used a stump and gates. This technique requires each lever be moved to a precise distance (typically, height) at which the stump can pass through the gate. Overlifting or underlifting a lever causes it to block the stump; older locks' levers only needed to be moved far enough — more than that had no effect, as long as they cleared the obstacle. Barron, and after him his son, and others, used only the arrangement of stumps on the tumblers with gates in the bolt tail. This arrangement would prove in the long run less successful than Barron's other suggestion of a stump on the bolt tail and gates in the tumblers.
The double-acting movable detainer principle is still in use to this day, including [[pin-tumbler]] locks by [[Linus_Yale_Jr|Linus Yale, Jr]].

=== Chubb lock ===
[[File:Chubb_lock.jpg|thumb|right|text-top|300px|The [[Chubb]] Detector lock.]]

In 1818, Charles and [[Jeremiah Chubb]] patented [BP4219] a lock design based on Barron's work. Their version used the placement of stump on the bolt tail and gates in the levers. This design is commonly associated with the name of Chubb, and is still in use today in many locks. They also added a device called the ''detector'', an extra lever that triggered by overlifting of the main levers. When triggered, the detector would lock the bolt until it was reset [regulated, in Chubbs' word] with a special key. To make it more convenient to use,the Chubb detector lock was modified slightly in 1824 so that it could be reset by the working key, instead of a separate 'regulating' key. The concept of the ‘detector’ was that the lock not only responded to the true key, it also recognised a wrong key or picking attempt, and signalled this to the proper keyholder by a change of state. The concept was invented by Ruxton in 1816 [BP4027] but his realisation was not a practical success. The Chubb lock was the first to have a practical detector, combined with lever tumblers. [[Chubb]] later added false notches or serrations on the fences of the levers which prematurely bound components if tension were applied when the component was in the incorrect position. This anti-picking idea was originally introduced on Bramah locks from 1817, and also used on Strutt's lever lock of 1819 — the first to use end-gated levers. It was later included in [[security pins]] many other lock designs.
In 1820, Mallet patented a rotating barrel and curtain that closed off the keyhole when the key was turned and hindered independant movement of picking instuments. This addition helped to prevent [[decoding]]. De La Fons would later also be granted a patent for this same idea, in 1846. Although not widely used before 1851, the combined barrel-and-curtain are now commonly used security features of high-security lever locks.

=== Tucker and Reeves ===
In 1851, a new design surfaced with a bolt that was not rigidly fixed but could shift on one end. Patented by Tucker and Reeves, this design aimed to thwart picking attempts involving pressure on the bolt. The shifting bolt made it harder to feel the gates inside the lock as it shifted. In 1853, the design was refined to include a rotating barrel that prevented movement of the bolt until a key was inserted.

=== Parsons lock ===
Another form of ‘lever’ lock was Thomas Parsons’ balance lock [BP8350]of 1832. This originally had a plurality of levers pivoted around their midpoint (earlier levers were pivoted at one endpoint)below the bolt tail, each lever having a hook (of differing lengths)at both ends. Spring pressure pressed the hooks at one end into a notch in the bolt tail, (locking the bolt against movement). The key steps pushed on the other ends of the levers. The key bit pressed those ends towards the bolt, which had notches for these hooks also. (There are two notches each end of the bolt tail, for the shot and withdrawn positions of the bolt.) The correct key balanced every lever with neither end hooking into the bolt. Because the balance levers take little strain, they can be thin, so that using 7 was common, and up to 20 in some safe locks.
This linear lock enjoyed considerable success in the 19th C. A cylinder locking device version made by CAWI appeared in 1951, using essentially the same idea, differently realised.

Numerous detail variations in the lever mechanism have been invented. There have also appeared several lever cylinder locking devices, of which the Ingersoll Impregnable is notable. It has been made under licence in the USA by Sargant & Greenleaf.

== Principles of Operation ==

A series of levers is placed in the lock. The entire set of levers must be properly raised by the key to allow a piece of metal connected to the bolt to pass through the gates of the levers, retracting or extending the bolt. Each lever may have a larger undersection or a different gate position to provide [[differs]].

<div align="center"><gallery>
</gallery></div>

== Components ==

; Levers
: The primary locking component of lever lock. Each lever is a flat piece of metal with a gate which must be raised to the proper position to allow the stump to pass through and retract or extend the bolt. Each lever is normally impelled by a spring, usually fixed to the lever. Some levers use a thinned belly section referred to as "conning" to ensure the lever interfaces with the correct bitting area on the key.

; Stump
: The stump is a protrusion usually fixed to the [[bolt]]. The stump prevents the bolt from being extended or retracted until the levers are properly positioned. Traditional designs have the stump and levers interconnected (pockets are closed, with the stump sitting inside each lever).

; Washers
: Washers are flat metal plates placed between each lever to ensure that each lever is properly raised by each bitting cut. They are not universal, but common in outdoor facing lever locks that require a high degree of reliability, especially in harsh conditions.

; Barrel and Curtain (now combined and usually referred to simply as 'curtain')
: A curtain is a component used in the keyhole to prevent direct access to the levers after the key or pick is rotated in the lock. This protects against casual manipulation of the levers, but does not preclude [[lockpicking]] attacks completely.

== Vulnerabilities ==

Lever locks (in common with other locks)are vulnerable to a variety of attacks, depending on their design. Tools to pick and decode lever locks are not as widely available as their [[pin-tumbler]] counterparts, largely because the tools required are more expensive, and specialized to each lock, unlike pin tumbler and wafer tumbler [[picks]]. However, devices do exist and can be effective. Often, tools must be made of a size and design for an individual model of lever lock. In general, well-made lever locks incorporating several pick-resisting features are likely to be physically stronger and more resistant to manipulation than comparable pin tumbler cylinder locks. They are likely to be larger, and typically have slightly larger keys. Lever locks in widespread use tend to have fewer differs than comparable pin tumbler cylinder locks, although trial of keys is hindered by the greater weight of keys needed. Lever locks are not well-suited to complex large-scale or multi-level masterkeying. One- and two-level masterkeying has been much used in institutions in the past.

* [[Lockpicking]]
* [[Impressioning]]
* [[Decoding]]
* [[Bypass]]

'''Notes'''
* Lever locks are not subject to [[key bumping]] or [[pick gun]] attacks.

== References ==
<references />

== See also ==

* [[Lock]]
* [[Key]]
* [[Lockpicking]]

[[Category:Locks]]
[[Category:Lever locks| ]]

Lever

2012-11-26T20:15:09Z

Rphillips52: /* Lever */ Detail additions of patent numbers names, dates, and additional details and clarifications.