Kwikset Classic - Revision history

Sandplum: /* Kwikset Classic */ added photo of deadbolt with keyway and logo

2021-05-26T15:33:02Z

Kwikset Classic: added photo of deadbolt with keyway and logo

← Older revision		Revision as of 15:33, 26 May 2021
Line 3:		Line 3:
	{{Lock model		{{Lock model
	\|name=Kwikset Classic		\|name=Kwikset Classic
	\|Img=		\|Img=File:Kwikset_keyway_logo.png
	\|maker=[[Kwikset]]		\|maker=[[Kwikset]]
	\|lock_type=[[Cylinder]]		\|lock_type=[[Cylinder]]

2021-03-06T21:03:27Z

2019-03-09T06:11:46Z

Principles of operation: the seventh cut depth is used with master pins OR construction balls

← Older revision		Revision as of 06:11, 9 March 2019
Line 24:		Line 24:
	:''See also: [[Pin-tumbler#Principles_of_Operation\|Pin-Tumbler (Principles of Operation)]]''		:''See also: [[Pin-tumbler#Principles_of_Operation\|Pin-Tumbler (Principles of Operation)]]''

	The Classic is a traditional pin-tumbler that uses five pin stacks. To open the lock, all pin stacks must be aligned at the [[shear line]] to allow the [[plug]] to rotate. There are six key pin heights and seven key cut depths with ~~the use of~~ [[Master keying\|master pins]]. The Classic has a [[MACS]] of 4. Many Classic cylinders come with [[construction keying]] dimples on the plug.		The Classic is a traditional pin-tumbler that uses five pin stacks. To open the lock, all pin stacks must be aligned at the [[shear line]] to allow the [[plug]] to rotate. There are six key pin heights and seven key cut depths, the seventh only used when combined with [[Master keying\|master pins]] or construction balls. The Classic has a [[MACS]] of 4. Many Classic cylinders come with [[construction keying]] dimples on the plug.

	The Classic uses key pins that are slightly tapered on both ends. Classic cylinders do not require use of any [[security pin]]s, but often come with a couple spool drivers.		The Classic uses key pins that are slightly tapered on both ends. Classic cylinders do not require use of any [[security pin]]s, but often come with a couple spool drivers.

2019-03-09T05:39:24Z

Principles of operation: Some Kwikset locks do come with spool drivers.

← Older revision		Revision as of 05:39, 9 March 2019
Line 26:		Line 26:
	The Classic is a traditional pin-tumbler that uses five pin stacks. To open the lock, all pin stacks must be aligned at the [[shear line]] to allow the [[plug]] to rotate. There are six key pin heights and seven key cut depths with the use of [[Master keying\|master pins]]. The Classic has a [[MACS]] of 4. Many Classic cylinders come with [[construction keying]] dimples on the plug.		The Classic is a traditional pin-tumbler that uses five pin stacks. To open the lock, all pin stacks must be aligned at the [[shear line]] to allow the [[plug]] to rotate. There are six key pin heights and seven key cut depths with the use of [[Master keying\|master pins]]. The Classic has a [[MACS]] of 4. Many Classic cylinders come with [[construction keying]] dimples on the plug.

	The Classic uses key pins that are slightly tapered on both ends. Classic cylinders do not use any [[security pin]]s.		The Classic uses key pins that are slightly tapered on both ends. Classic cylinders do not require use of any [[security pin]]s, but often come with a couple spool drivers.


	== Keying Specifications ==		== Keying Specifications ==

2011-11-02T16:54:57Z

2011-11-01T23:48:38Z

How to Remove the Cylinder from the Kwikset Knob: corrected ref link

← Older revision		Revision as of 23:48, 1 November 2011
Line 55:		Line 55:
	== How to Remove the Cylinder from the Kwikset Knob ==		== How to Remove the Cylinder from the Kwikset Knob ==

	# Using the Cylinder Removing Tool, rotate the round spindle until the tab lines up with the bolt stems.<ref>Kwikset Rekeying Manual [www.kwikset.com/Libraries/Literature/Rekeying_Manual.sflb.ashx].</ref>		# Using the Cylinder Removing Tool, rotate the round spindle until the tab lines up with the bolt stems.<ref>Kwikset Rekeying Manual [http://www.kwikset.com/Libraries/Literature/Rekeying_Manual.sflb.ashx].</ref>
	# Slide the tool under the spring housing behind the spindle and push to release the retainer. Pull out the spindle without rotating it.		# Slide the tool under the spring housing behind the spindle and push to release the retainer. Pull out the spindle without rotating it.
	# Slide the tool into the empty spindle chamber, angling it to bypass the cover at the top of the hole. Push the tool all the way in and apply pressure until the cylinder is forced out of the front of the knob.		# Slide the tool into the empty spindle chamber, angling it to bypass the cover at the top of the hole. Push the tool all the way in and apply pressure until the cylinder is forced out of the front of the knob.


	== Vulnerabilities ==		== Vulnerabilities ==

2011-11-01T23:47:24Z

added knob cylinder removal instructions

← Older revision		Revision as of 23:47, 1 November 2011
Line 52:		Line 52:
	# Remove the plug from the core, either by using a working key or manipulating the pins so that they do not block the shear line.		# Remove the plug from the core, either by using a working key or manipulating the pins so that they do not block the shear line.


			== How to Remove the Cylinder from the Kwikset Knob ==

			# Using the Cylinder Removing Tool, rotate the round spindle until the tab lines up with the bolt stems.<ref>Kwikset Rekeying Manual [www.kwikset.com/Libraries/Literature/Rekeying_Manual.sflb.ashx].</ref>
			# Slide the tool under the spring housing behind the spindle and push to release the retainer. Pull out the spindle without rotating it.
			# Slide the tool into the empty spindle chamber, angling it to bypass the cover at the top of the hole. Push the tool all the way in and apply pressure until the cylinder is forced out of the front of the knob.

2011-10-29T18:19:24Z

Vulnerabilities: added Bumping

2011-10-28T14:43:56Z

added category

2011-10-28T14:40:57Z

formated specification table

← Older revision		Revision as of 14:40, 28 October 2011
Line 27:		Line 27:


			<pre>
	Cut \| Spacing \| Depth \| Key Pin \| Master \| Driver		Cut \| Spacing \| Depth \| Key Pin \| Master \| Driver

	1 .247" .329" .172" .023" ~~.180"~~		1 .247" .329" .172" .023" .180"

	~~2 .397" .306" .195" .046" .180"~~

	~~3 .547" .283" .218" .069"~~ .180"

	4 .~~697~~" .~~260~~" .~~241~~" .~~092~~" .180"		2 .397" .306" .195" .046" .180"

	5 .~~847~~" .~~237~~" .~~264~~" .~~115~~" .180"		3 .547" .283" .218" .069" .180"

	6 .~~997~~" .~~214~~" .~~287~~" .~~138~~" .180"		4 .697" .260" .241" .092" .180"

	~~7 --~~ .~~191~~"		5 .847" .237" .264" .115" .180"

			6 .997" .214" .287" .138" .180"

			7 .191"
			</pre>

	== Disassembly instructions ==		== Disassembly instructions ==