ASSA d12: Difference between revisions
m (spec, rating) |
m (added the ref tag for the Han Fey link) |
||
| (3 intermediate revisions by 2 users not shown) | |||
| Line 7: | Line 7: | ||
| lock_type = [[Cylinder]] | | lock_type = [[Cylinder]] | ||
| lock_design = [[Pin_tumbler|Pin-tumbler]] | | lock_design = [[Pin_tumbler|Pin-tumbler]] | ||
| years_produced = 2010 | |||
| ratings = EN 1303 | | ratings = EN 1303 | ||
| related = [[ASSA 700]] | | related = [[ASSA 700]] | ||
| Line 15: | Line 16: | ||
The '''d12''' is a medium security EN 1303-rated [[Pin_tumbler|pin tumbler]] cylinder made by [[ASSA]] for residential or commercial use. It is intended as a successor to the [[ASSA 700]] series which dates back to 1948. The d12 features six pins and numerous security improvements over the original cylinder, including a paracentric keyway and patented key profiles. | The '''d12''' is a medium security EN 1303-rated [[Pin_tumbler|pin tumbler]] cylinder made by [[ASSA]] for residential or commercial use. It is intended as a successor to the [[ASSA 700]] series which dates back to 1948. The d12 features six pins and numerous security improvements over the original cylinder, including a paracentric keyway and patented key profiles. | ||
There are two main models: | |||
* model 13XX featuring usual six pins (referred to as Level 1 in Han Fey's document) and no protection against unauthorized key copying. | |||
* model 12XX featuring a checkpin interacting with the secondary bitting at the front of the key, close to its spine (referred to as Level 2 in the Han Fey's document), that is protected from unauthorized key copying.<ref>[http://hanfeylocktechnologies.com/Han_Fey_ASSA_d12.pdf Fey, Han (2011). ''The ASSA d12 and some other Swedish products''.]</ref> | |||
Each of those models seem to have one more sub-model (designed 0200 and 0300), that according to the product sheets are not considered as approved locking devices (godkänd låsenhet) by the insurance companies. | |||
__TOC__ | __TOC__ | ||
| Line 20: | Line 26: | ||
== Principles of operation == | == Principles of operation == | ||
'''d12''' key has two cuts for every keypin, which doesn't have to be at the same height. Combined with the double spiked keypins, where the spikes doesn't have the be the same height, allows some form of masterkeying, not requiring master wafers. This adds to the overall security of the lock as there doesn't have to be additional shearlines. | |||
The Level 2 model has at least one keypin in one of the last two chambers switched for a higher checkpin, that interacts with the secondary bitting at the tip of the key. | |||
All driver pins are ASSA barrel spools and all chambers have the matching counter-milling, which coupled with the keyway design leads to high resistance against lockpicking. All core chambers also contain two grooves, that have several functions: first of all, they ensure the keypin can't rotate, which could render the lock inoperable; the second function is to prevent bumping (or at least make it very hard) - each keypin's wings end in different heights, which causes the tops of the pins stay in different heights. | |||
The core has two holes on both the left and the right side, that seem to be aligned with the first chamber, which would suggest the possibility of the construction keying. | |||
<div align="center"><gallery> | <div align="center"><gallery> | ||
| Line 49: | Line 60: | ||
# Insert the key and turn the plug 45-90 degrees. | # Insert the key and turn the plug 45-90 degrees. | ||
# Withdraw the plug from the cylinder. (A [[Plug_follower|plug follower]] is recommended) | # Withdraw the plug from the cylinder. (A [[Plug_follower|plug follower]] is recommended) | ||
When reassembling the lock, always check with the key if all the keypins rest at the shearline - if a pin is turned around, chances are it will be either too deep or too high, rendering the key not working. | |||
== Vulnerabilities == | == Vulnerabilities == | ||
| Line 67: | Line 80: | ||
File:ASSA d12 plug-Reinder.png |ASSA d12 plug. | File:ASSA d12 plug-Reinder.png |ASSA d12 plug. | ||
File:ASSA d12 plug2-Reinder.png |ASSA d12 plug. | File:ASSA d12 plug2-Reinder.png |ASSA d12 plug. | ||
File:Assa D12 L2 least.png |ASSA d1201. | |||
File:Assa D12 L2 keyway least.png |ASSA d1201 keyway detail. | |||
File:Assa D12 L2 key least.png |ASSA d1201 key. | |||
File:Assa D12 L2 bitting least.png |ASSA d1201 detail of the key bitting. | |||
File:Assa D12 L2 pins least.png |ASSA d1201 pins. | |||
File:Assa D12 L2 pin detail least.png |ASSA d1201 detail of the double spiked keypin. | |||
File:Assa D12 L2 checkpin detail least.png |ASSA d1201 detail of the checkpin. | |||
File:Assa D12 L2 core checkpin least.png |ASSA d1201 detail of the core with protruding checkpin. | |||
File:Assa D12 L2 core bottom least.png |ASSA d1201 core bottom view. | |||
File:Assa D12 L2 core left least.png |ASSA d1201 core viewed from the left. | |||
File:Assa D12 L2 core right least.png |ASSA d1201 core viewed from the right. | |||
File:Assa D12 L2 core top least.png |ASSA d1201 core viewed from the top. | |||
File:Assa D12 L2 core milling least.png |ASSA d1201 core milling detail. | |||
File:Assa D12 L2 core tracks least.png |ASSA d1201 keypin chambers tracks detail. | |||
File:Assa D12 L2 core back least.png |ASSA d1201 core from the back without the backplate. | |||
File:Assa D12 L2 core backplate least.png |ASSA d1201 core with the backplate. | |||
File:Assa D12 L2 bible least.png |ASSA d1201 bible (the sidebar groove is not used in this model). | |||
</gallery></div> | </gallery></div> | ||
== References == | == References == | ||
<references /> | <references /> | ||
== External links == | == External links == | ||
* [ | * [https://www.assaabloy.com/se/sv/solutions/products/mekaniska-lassystem-cylindrar/konsumentcylindrar/d12-serien/d12-1200 ASSA d12 1200 product page (Swedish)] | ||
* [ | * [https://www.assaabloy.com/se/sv/solutions/products/mekaniska-lassystem-cylindrar/konsumentcylindrar/d12-serien/d12-0200 ASSA d12 0200 product page (Swedish)] | ||
* [https://www.assaabloy.com/se/sv/solutions/products/mekaniska-lassystem-cylindrar/konsumentcylindrar/basic-serien/basic-1300 Assa Basic 1300 product page (Swedish)] | |||
* [https://www.assaabloy.com/se/sv/solutions/products/mekaniska-lassystem-cylindrar/konsumentcylindrar/basic-serien/basic-0300 Assa Basic 0300 product page (Swedish)] | |||
* [http://blackbag.nl/?p=1788 Differences between ASSA 700 and ASSA d12] | * [http://blackbag.nl/?p=1788 Differences between ASSA 700 and ASSA d12] | ||
== See also == | == See also == | ||
| Line 82: | Line 116: | ||
* [[ASSA-Abloy]] | * [[ASSA-Abloy]] | ||
* [[Pin_tumbler|Pin-tumbler]] | * [[Pin_tumbler|Pin-tumbler]] | ||
[[Category:Lock models]] | [[Category:Lock models]] | ||
Latest revision as of 10:03, 26 February 2023
ASSA d12
| ASSA d12 | |
 | |
| Name | ASSA d12 |
|---|---|
| Manufacturer | ASSA |
| Lock Type | Cylinder |
| Lock Design | Pin-tumbler |
| Year(s) Produced | 2010 |
| Security Rating(s) | EN 1303 |
| Specifications | |
| # of Components | 6 |
| Component Type | Pin-tumbler |
| Related Locks | |
| ASSA 700 | |
The d12 is a medium security EN 1303-rated pin tumbler cylinder made by ASSA for residential or commercial use. It is intended as a successor to the ASSA 700 series which dates back to 1948. The d12 features six pins and numerous security improvements over the original cylinder, including a paracentric keyway and patented key profiles.
There are two main models:
- model 13XX featuring usual six pins (referred to as Level 1 in Han Fey's document) and no protection against unauthorized key copying.
- model 12XX featuring a checkpin interacting with the secondary bitting at the front of the key, close to its spine (referred to as Level 2 in the Han Fey's document), that is protected from unauthorized key copying.[1]
Each of those models seem to have one more sub-model (designed 0200 and 0300), that according to the product sheets are not considered as approved locking devices (godkänd låsenhet) by the insurance companies.
Principles of operation
d12 key has two cuts for every keypin, which doesn't have to be at the same height. Combined with the double spiked keypins, where the spikes doesn't have the be the same height, allows some form of masterkeying, not requiring master wafers. This adds to the overall security of the lock as there doesn't have to be additional shearlines.
The Level 2 model has at least one keypin in one of the last two chambers switched for a higher checkpin, that interacts with the secondary bitting at the tip of the key.
All driver pins are ASSA barrel spools and all chambers have the matching counter-milling, which coupled with the keyway design leads to high resistance against lockpicking. All core chambers also contain two grooves, that have several functions: first of all, they ensure the keypin can't rotate, which could render the lock inoperable; the second function is to prevent bumping (or at least make it very hard) - each keypin's wings end in different heights, which causes the tops of the pins stay in different heights.
The core has two holes on both the left and the right side, that seem to be aligned with the first chamber, which would suggest the possibility of the construction keying.
Cuts on a TrioVing d12 key.
ASSA d12 key pins and drivers.
Disassembly instructions
There are two main assemblies this lock can be found in which will vary by branding and format. One uses a C-clip on the back on the plug while the other uses a large retaining screw.
If the lock uses the retaining screw:
- Unscrew the Torx screw on the tailpiece and remove the wafer beneath it.
- Unscrew the retaining screw from the rear of the plug.
- Unscrew and remove the closing rod over the pin chambers (be careful not to allow springs to escape).
- Remove the driver pins and springs. They are all the same so there is no need to keep them in order. Key pins cannot fit through the top chambers.
- Slide the plug out of the housing.
Disassembly using a follower is possible but not recommended due to the threads on the back of the plug that accept the retaining screw.
If the lock uses a C-clip:
- Remove the C-clip.
- Insert the key and turn the plug 45-90 degrees.
- Withdraw the plug from the cylinder. (A plug follower is recommended)
When reassembling the lock, always check with the key if all the keypins rest at the shearline - if a pin is turned around, chances are it will be either too deep or too high, rendering the key not working.
Vulnerabilities
The ASSA d12 may be vulnerable to one or more of the following:
Gallery
Scandinavian profile ASSA d12 (back).
Level 1 d12 key. Bo Widén and d12 logo on right side of bow.
An ASSA d12 key profile.
An ASSA d12 keyway.
ASSA d12 plug.
ASSA d12 plug.
ASSA d1201.
ASSA d1201 keyway detail.
ASSA d1201 key.
ASSA d1201 detail of the key bitting.
ASSA d1201 pins.
ASSA d1201 detail of the double spiked keypin.
ASSA d1201 detail of the checkpin.
ASSA d1201 detail of the core with protruding checkpin.
ASSA d1201 core bottom view.
ASSA d1201 core viewed from the left.
ASSA d1201 core viewed from the right.
ASSA d1201 core viewed from the top.
ASSA d1201 core milling detail.
ASSA d1201 keypin chambers tracks detail.
ASSA d1201 core from the back without the backplate.
ASSA d1201 core with the backplate.
ASSA d1201 bible (the sidebar groove is not used in this model).
References
External links
- ASSA d12 1200 product page (Swedish)
- ASSA d12 0200 product page (Swedish)
- Assa Basic 1300 product page (Swedish)
- Assa Basic 0300 product page (Swedish)
- Differences between ASSA 700 and ASSA d12
