Testing-mgsecure: Difference between revisions

From Lockwiki
Jump to navigationJump to search
Line 170: Line 170:
File:Lockwood 120-50.jpg | [[Lockwood 120 series]]
File:Lockwood 120-50.jpg | [[Lockwood 120 series]]
File:Lockwood 334B45.jpg | [[Lockwood 334 series]]
File:Lockwood 334B45.jpg | [[Lockwood 334 series]]
File:LockwoodTwin Key.jpeg | [[Lockwood Twin]]
File:Mark IV Manifoil dial-TomEklof.jpg | [[Mark IV Manifoil]]
File:Mark IV Manifoil dial-TomEklof.jpg | [[Mark IV Manifoil]]
File:Mastercommercial.JPG | [[Master Lock No 1]]
File:Mastercommercial.JPG | [[Master Lock No 1]]
Line 179: Line 178:
File:Master Lock 150 - FXE47400.jpg | [[Master Lock No 150]]
File:Master Lock 150 - FXE47400.jpg | [[Master Lock No 150]]
File:Master175XDLF-front.JPG | [[Master Lock No 175]]
File:Master175XDLF-front.JPG | [[Master Lock No 175]]
File:MasterNo2.jpeg | [[Master Lock No 2]]
File:MasterNo22.jpg | [[Master Lock No 22]]
File:MasterNo22.jpg | [[Master Lock No 22]]
File:Master2240.JPG | [[Master Lock No 2240]]
File:Master2240.JPG | [[Master Lock No 2240]]
File:Master Lock 3 - FXE47401.jpg | [[Master Lock No 3]]
File:Master Lock 3 - FXE47401.jpg | [[Master Lock No 3]]
File:MasterNo4.jpg | [[Master Lock No 4]]
File:Master Lock 410 LOTO, orange - FXE47410.jpg | [[Master Lock No 410]]
File:Master Lock 410 LOTO, orange - FXE47410.jpg | [[Master Lock No 410]]
File:Master 570.jpg | [[Master Lock No 570]]
File:Master605.JPG | [[Master Lock No 605]]
File:Master605.JPG | [[Master Lock No 605]]
File:Master975-front.jpg | [[Master Lock No 975]]
File:Lock Sphero.jpg | [[Master Lock Sphero]]
File:Lock Sphero.jpg | [[Master Lock Sphero]]
File:Medeco Biaxial cylinder.jpg | [[Medeco Biaxial]]
File:Medeco Biaxial cylinder.jpg | [[Medeco Biaxial]]
Line 201: Line 196:
File:MIWA VM99 cylinder.jpg | [[MIWA VM99]]
File:MIWA VM99 cylinder.jpg | [[MIWA VM99]]
File:MTL Interactive front view - FXE48058.jpg | [[Mul-T-Lock Interactive]]
File:MTL Interactive front view - FXE48058.jpg | [[Mul-T-Lock Interactive]]
File:Lock Cylinder.JPG | [[Mul-T-Lock Interactive+]]
File:Dimple-MTL Jr keyway lighter - FXE44819.jpg | [[Mul-T-Lock Junior]]
File:Dimple-MTL Jr keyway lighter - FXE44819.jpg | [[Mul-T-Lock Junior]]
File:Mersey Lock 04.jpg | [[NATO Mersey]]
File:Mersey Lock 04.jpg | [[NATO Mersey]]
Line 219: Line 213:
File:S&G 8430 Group 1R inside with Tab lock.jpg | [[S&G 8430]]
File:S&G 8430 Group 1R inside with Tab lock.jpg | [[S&G 8430]]
File:8500 spring not charged.png | [[S&G 8500]]
File:8500 spring not charged.png | [[S&G 8500]]
File:S&G 951C.jpg | [[S&G 951]]
File:Sargent Signature face cropped.jpg | [[Sargent Signature]]
File:Sargent Signature face cropped.jpg | [[Sargent Signature]]
File:Schlage Everest cylinder.jpg | [[Schlage Everest]]
File:Schlage Everest cylinder.jpg | [[Schlage Everest]]

Revision as of 15:55, 1 February 2023


This page being used for testing and development




Disassembly instructions edit

Original: To disassemble a double euro cylinder, use of a pinning shoe is the preferred method. Other possibility is to use a segmented follower, but that requires that both cores are pulled out a bit to allow a cam removal. Then a core should be rotated to approximately 4:30 or 7:30 o'clock position (135 degrees either clockwise or anti-clockwise) to prevent driver entering a gaps for the cam clutch. Then a segmented follower can be used to remove the core.

Proposed edit:

For Euro Profile page:

The use of a pinning shoe is the preferred method for disassembling a double euro cylinder. STEPS?

Another method is to use a segmented follower. The c-clips retaining both cores must first be removed and then both cores can be pulled out slightly in order to remove the center cam. One core should be rotated 30-45 degrees either clockwise or counter-clockwise -- once the cam is removed. This allows the core to be removed without driver pins entering gaps for the cam clutch. At that point, a segmented follower can be used to remove the core.

Locks not intended for installation and use can be disassembled in a quick but destructive procedure. The cylinder housing itself can be cut in the middle using a hacksaw or grinder. The cam will no longer be held in place and can be removed. The resulting two cut half euro cylinders can then be disassembled as outlined above.

For individual lock page:

TBD


Images without author tags

ALL lock photos

Test gallery